Industrial Area 10, Store 7, Sharjah ยท Ready stock ยท Supply across the UAE

+971 52 684 9954WhatsApp amaalazim@yahoo.com

Weldolet vs Sockolet vs Threadolet: Branch Outlet Fittings Explained

Weldolet vs sockolet vs threadolet: how each olet connects, which pressure class and branch size suits it, and what to specify when ordering in the UAE.
  • Ready stock in Sharjah
  • ASTM / ASME / BS / EN grades
  • Supply across the UAE
Carbon steel weldolet, sockolet and threadolet branch outlet fittings welded onto a run pipe

In this guide

When a smaller line has to branch off a larger header, a full tee is not always the best answer. On many industrial, fire fighting and HVAC lines, the branch is made with an olet: a forged outlet fitting welded straight onto the run pipe. The three you will meet most often are the weldolet, the sockolet and the threadolet, and the choice of weldolet vs sockolet vs threadolet comes down to one question: how will the branch pipe be joined?

This guide explains how each one works, where it fits best, and what to put on your enquiry so the right outlet arrives on site.

What Is an Olet?

An olet is a branch outlet fitting. A hole is cut in the run (header) pipe, the olet is placed over it, and its base is welded to the run pipe. The top of the olet then provides the connection for the branch line, usually at 90ยฐ. Olets are forged and shaped to give the branch connection integral reinforcement, so in many cases no separate reinforcing pad is needed. The common reference standard for these integrally reinforced forged branch outlets is MSS SP-97.

Compared with a tee, an olet:

  • needs only one weld to the header instead of cutting the header and making three butt welds;
  • lets you add a branch to an existing header without replacing a section of pipe;
  • suits branches that are much smaller than the run, where a reducing tee would be bulky or unavailable.

Weldolet

A weldolet has a bevelled outlet, so the branch pipe is butt-welded to it. Because the branch joint is a full-penetration butt weld, the weldolet is the usual choice for larger branch sizes, higher pressures and critical services where welds will be radiographed. The outlet bore and wall thickness are matched to the branch pipe schedule, for example standard weight, Sch 80 or XS, so the bevels line up.

Typical uses: branch lines off fire fighting mains, process and utility headers, chilled water headers and anywhere the rest of the system is butt welded. See our MS weldolet page for the sizes we supply.

Sockolet

A sockolet has a socket outlet. The branch pipe is pushed into the socket and fillet-welded around the outside. This is a socket-weld joint, so sockolets are mainly used on small-bore branches, where they make fit-up quicker and avoid the precise bevel alignment a butt weld needs. Sockolets are rated by pressure class, commonly Class 3000 and Class 6000, which should match the rest of the socket-weld fittings on the line.

Typical uses: small drain, vent and instrument branches, sampling points and small utility take-offs. Leave a small gap at the bottom of the socket before welding, as for any socket-weld joint, to allow for weld shrinkage. See our MS sockolet page for details.

Threadolet

A threadolet has a female threaded outlet. It is welded to the header like the others, but the branch connects by screwing in a threaded pipe, nipple or instrument. That makes it the go-to fitting for pressure gauges, temperature sensors, test points, drains and vents, or any small connection that may need to be removed later. Threadolets are also made in pressure classes such as 3000 and 6000.

Always confirm the thread standard: NPT and BSP threads look alike but do not seal properly together. Our NPT vs BSP guide explains how to tell them apart. See our MS threadolet page for the range.

Weldolet vs Sockolet vs Threadolet: Side-by-Side

FeatureWeldoletSockoletThreadolet
Branch connectionButt weld (bevelled end)Socket weld (fillet weld)Female thread
Rating basisMatched to branch pipe schedulePressure class (e.g. 3000, 6000)Pressure class (e.g. 3000, 6000)
Typical branch sizeSmall to large boreSmall boreSmall bore
Weld inspectionBranch weld can be radiographedFillet weld, surface inspectionNo branch weld
Removable branchNoNoYes
Common usesMain branch lines, high pressure and critical serviceDrains, vents, small utility branchesGauges, sensors, test points, drains

All three are welded to the run pipe in the same way; the difference is only at the branch end. If you are still deciding which joining method suits your system overall, our comparison of threaded vs butt-weld vs socket-weld fittings covers the wider trade-offs.

Other Olet Types You May See on Drawings

  • Latrolet: for a 45ยฐ lateral branch instead of 90ยฐ.
  • Elbolet: fitted on the outside of a long radius elbow, often for a thermowell or drain.
  • Nipolet: an olet with an integral nipple, used for small valved drains and vents.
  • Flangeolet: provides a flanged branch connection directly on the header.

These are specified for particular layouts. If one appears on your isometrics, send us the drawing reference and we will advise on availability.

How to Size and Specify an Olet

An olet has two sizes: the run size (the header it sits on) and the branch size (its outlet). The base is contoured to fit the curvature of the run pipe, so a 1″ outlet made for a 6″ header will not sit correctly on a 10″ header. Many manufacturers cover a band of run sizes with one base, but you should always state both.

Include these details in your enquiry:

  1. Type: weldolet, sockolet or threadolet
  2. Branch (outlet) size, for example 1″
  3. Run (header) size, for example 6″
  4. Schedule (for weldolets) or pressure class (for sockolets and threadolets)
  5. Thread type for threadolets: NPT or BSP
  6. Material, for example carbon steel to suit a carbon steel header
  7. Quantity and any certificate requirements

Installation Tips

  • Cut the right hole. The opening in the header should match the olet bore. Remove burrs and slag so nothing restricts flow or breaks loose later.
  • Use a qualified welding procedure. The weld from olet to header is a structural branch weld; follow the project WPS and inspection plan.
  • Protect threads during welding. On threadolets, keep spatter and heat distortion away from the thread.
  • Match materials. Weld carbon steel olets to carbon steel pipe to avoid dissimilar-metal welding and corrosion problems.

For high-pressure systems, the same principles apply as for other fittings. Our guide on choosing pipe fittings for high-pressure applications goes into ratings and materials in more depth.

Frequently Asked Questions

What is the difference between a weldolet and a sockolet?

Both are welded to the header. A weldolet takes the branch pipe with a butt weld, while a sockolet takes it with a socket weld (the pipe slides into a socket and is fillet welded).

When should I use a threadolet?

Use a threadolet for small connections that are screwed in, such as gauges, temperature sensors, test points, drains and vents, especially where the item may need to be removed for maintenance.

Is an olet better than a tee?

Neither is better in every case. Olets are efficient for branches much smaller than the header and for adding branches to existing lines. Full or reducing tees are often preferred when the branch is the same or close to the header size.

Do olets need a reinforcing pad?

Olets are designed with integral reinforcement, so a separate pad is not normally required. Always confirm against your piping code and project specification.

Buy Olets in Sharjah

Al Amaal Hardware supplies forged carbon steel MS threadolets, weldolets and sockolets for 90ยฐ branch connections from 1/8″ to 4″. We also stock MS butt weld fittings for the rest of your branch line.

Send us your list with olet type, branch and run sizes, schedule or class and quantity, and we will confirm availability and pricing. Request a quote or message us on WhatsApp for a fast response.

Need these items for a project?

Send the material, size and quantity. Our Sharjah team replies with price and stock availability.

Share this guide with your team

WhatsApp
LinkedIn
Facebook
Email

Published by

Al Amaal Hardware Team

Pipe fittings, flanges and valves supplier at Industrial Area 10, Store 7, Sharjah, UAE. Our guides are written from day-to-day experience matching materials, pressure classes and thread standards to real project requirements.

Always confirm project-critical dimensions and ratings against the governing standard (ASME, ASTM, BS, EN) or your consultant's specification.

Related guides

Get a price for this product

Send the size, material and quantity. We reply with price and stock by phone or WhatsApp.

Why contractors choose us

  • Walk-in store in Industrial Area 10, Sharjah
  • Carbon steel, stainless, brass, MI/GI and aluminium
  • Advice on material, pressure class and end connection
  • Quotes by WhatsApp, phone or email
Read our Google reviews โ†’

Need a price today?

Talk to our Sharjah sales desk directly.

Get in touch

Tell us what you need. We'll quote on WhatsApp.

Send the product, size and quantity. Our team replies with pricing and availability.

Get a Fast Quote + Trade Discount

Tell us the product you need. Our Sharjah sales team will call or WhatsApp you back with price and stock.